Sunday, May 17, 2015

Philips 40PFL5507H TV firmware restore

Came back home one day to an hourglass on the display of my TV, instead of the usual power up sequence.

IMG_0142

It just sat there for a couple of seconds before going to a blank screen. Reading online I found that it could be due to a corrupted firmware.

From the Philips website I downloaded a copy of the latest firmware and put it on a USB thumb-drive.

TV

However I was unable to get it to start the firmware installation process, regardless of the different methods that the help file included within the firmware download suggested.

I then looked around more and found a copy of the service manual for my TV here.

https://www.scribd.com/doc/178909518/40PFL5507H-12-pdf#download

In it, there was a method to invoke an alternate or backup software/firmware function, to be used in the event the default upgrade application does not start (sounds like me).

1. Disconnect TV from power.

2. Hold the DOWN cursor while reconnecting TV to mains.

3. Backup software application should start.

Following these steps I managed to restore the firmware on my TV (I had to go through channel setup as well, since those were lost)

IMG_0147

IMG_0148

With that done, I proceeded to enjoy some Discovery Channel. Smile

Tuesday, February 24, 2015

Yashica GT Pad of death + Rangefinder cleaning + Light seals

Picked up a Yashica GT for cheap (under USD$15) locally which was known to have the POD (pad of death) issue, basically a small foam piece inside goes crumbly and then the shutter will start going crazy.

IMG_1762

First steps are to disassemble the camera until you can see where the pad is.

IMG_1764

Here I’ve removed the advance lever.

IMG_1765

I planned to do this over the course of a few days, so bagging and labeling the parts was important, putting it all together and then finding out you have some stuff still on the bench is not cool (been there done that).

IMG_1766

ASA dial comes off next.

IMG_1768

Below that is a little washer which is basically what keeps the stationary part of the dial in place.

IMG_1769

 

IMG_1770

Now we have the film rewind knob

IMG_1771

I wrapped tape around a screwdriver for me to use as a leer against the knob.

IMG_1772

 

IMG_1773

There’s a small washer right under there.

IMG_1774

Below that there’s yet another washer that I guess keeps light and dust out of the innards.

IMG_1775

After removing 3 screws around the top cover,gently pop it off, there’s a wire still in there for the flash, so be careful.

IMG_1776

I chose to de-solder this wire so I wouldn’t have to be mindful of it while working on the camera.

IMG_1777

Residing within the top cover is the battery test button, I took it out before moving the top cover too much (prevents it from getting lost).

IMG_1778

Here we can see the problem, right there (just above CA in Yashica) is the deteriorated pad.

To get at it, you’d have to separate the lower mechanism from the upper. I did this by temporarily re-installing the advance lever, advancing and then using an allen key depress the lower mechanism.

IMG_1781IMG_1782

With that out of the way now, we can get at the pad, there are other methods that involve disassembling more of the camera so you get better access, however that involves removing part of the leatherette on the front of the camera, I didn’t want to risk damaging that so I chose to do it ‘surgically’.

IMG_1787

Here I’ve straightened out a bobby pin (from SWMBO) and put a small bend on the end to scrape out the remains, it helps if you can hold the camera upside down so the stuff falls out. Initially I wanted to use some of that black foam as the replacement material, but it was too soft.

IMG_1795

IMG_1796

For a far sturdier material I opted to use a small piece of eraser, the critical dimensions are 5mm x 4mm x 2mm.

Using the bent bobby pin and working upside down I leveraged the replacement piece into place.

IMG_1797

IMG_1798

Here it is back into place.

My camera had a sorta haze all over the rangefinder window, cleaning the glass and lenses that were reachable still didn’t quite cut it, contrast was really low on the RF patch, so I bit the bullet and attempted to clean the rangefinder innards.

IMG_1780

This copper plate is all that exists between the the innards and us. Using a utility knife I slowly leveraged it out. A few drops of cement are all that holds it on, it is quite thin and feels fragile though.

IMG_1785

Initially I cleaned everything in here with a Q-tip soaked in lens cleaner except for the beam splitting element (the gold coated piece), as I’ve heard that the coating can be extremely fragile, however the RF image was still not very clear because of the build up on there, so I went ahead and cleaned it anyways using no pressure at all (a damp Q-tip and then just dragged it over) the coating didn’t appear to be damaged, be very careful though, I’m not sure how much it takes to get it off.

I also replaced the light seals on my camera, they were starting to fall out in some places.

IMG_1799

IMG_1800

IMG_1801

Didn’t take too many pictures of this process but it’s really simple. I taped up the rear with a piece of paper and some tape to prevent anything from getting into the rear lens element area. Then using alcohol and a plastic pick (it was a dental pick thingy) I removed as much of the old seals as possible.

New light seals were cut out and re-glued back into place.

I’ve so far shot a roll of Ilford HP5+ through this camera and the results are really good, the metering is easy to use (either the shutter speed is too slow or fast, but you don’t know by how much) and the lens is fantastically sharp. Focus is spot on, on my camera at least, a pretty good deal for what I paid for this.

Smile